Description
Sprinter Driver Side Forward Fixed Glass OE Style Window | VWD SL101-F (2007-2026)
The VWD SL101-F is the OE-style, solid, fixed-glass upgrade for Sprinter vans. It replaces the old green tint look with grey solar privacy glass and a cleaner OEM appearance. Tempered safety glass, factory-stamping precision fit, and urethane-bonded installation for a sealed, rattle-free finish.
Key Features
- Solid fixed glass OE-style window
- Grey solar privacy glass with 17% UV filter rating
- Tempered safety glass built to DOT/SAE standards
- OEM precision fit using factory stampings
- Urethane-bonded installation for a weatherproof seal
- 1-year warranty
Fitment
- Vehicle: Mercedes-Benz Sprinter Van
- Years: 2007-2026
- Roof: Low roof or high roof
- Wheelbase: 144 or 170
- Position: Driver Side Forward (product page also lists Driver Side Sliding Door)
Technical Specifications
| Model | SL101-F |
| Window Type | Solid Fixed Glass OE Style |
| Overall Dimensions | 1402mm x 777mm (55.20 in x 30.6 in) |
| Glass | Grey Solar Privacy Tempered Safety Glass (17% UV Filter Rating) |
| Standards | DOT/SAE |
| Installation | Urethane Bonded |
| Warranty | 1 Year |
Installation
This is a urethane-bonded window. Prep the cutout, dry-fit, clean, prime, and set with automotive glass urethane. Tape and support during cure. Do not drive until the urethane has cured per the urethane manufacturer's specs. For the cleanest finish, use primer base and trim edge molding on the cut edge.
Mercedes Sprinter SL101 Installation Overview
Installing the SL101 driver-side forward windows requires removing a portion of the inner stamped sheet metal on compatible Mercedes-Benz Sprinter vans.
This installation overview applies to:
- SL101-AW – Premium Awning Window
- SL101-CA – Crank-Out Awning Window
- SL101-DS – Double-Sliding Window
- SL101-F – Fixed Glass Window
- SL101-SE – SE-Series Sliding Window
- SL101-SER – Rear-Opening Sliding Window
- 2007–2026 Mercedes-Benz Sprinter
- Driver Side Forward Position
The general process is:
- Identify and carefully cut the required inner sheet metal from inside the van when possible.
- File and deburr the cut edges to remove any sharp or raised areas.
- Prime or protect all freshly exposed steel.
- Install Trim-Lok edge molding over the finished sheet-metal edge.
- Clean all metal debris from the wall cavity.
- Dry-fit the actual SL101 window and verify complete clearance before applying automotive urethane.
- Urethane-bond the window in place and allow the adhesive to fully cure.
Important: Always verify the actual Sprinter configuration, wheelbase, and exact SL101 window before cutting. The illustrated cut area is for reference only and is not an exact cutting template.
FAQ
What vehicles does this window fit?
Mercedes-Benz Sprinter Van 2007-2026, 144- or 170-wheelbase, low or high roof.
What position is this window for?
It's listed for the Sprinter driver's-side front position. The product page also lists the driver's side sliding door as an additional window position.
What are the measurements?
Overall: 1402mm x 777mm (55.20 in x 30.6 in).
What tint is used?
Grey solar privacy glass with a 17% UV filter rating.
How is it installed?
Urethane-bonded installation.
Vehicle Fitment Guide
Mercedes-Benz Sprinter Van
| Model | Sprinter Van |
|---|---|
| Wheelbase | 144" or 170" |
| Model Years | 2007–2026 |
| Roof Height | Low Roof or High Roof |
Designed to fit Mercedes-Benz Sprinter vans within the configurations listed above.