CRL Universal Awning Van Windows

The newest thing in van windows is CRL "All Glass Look" selection for Full-Size Vans. The CRL Awning style window has become a go-to window for Camper Van Conversions. Whether you're converting a Sprinter, ProMaster, Transit or other Van this FW904RS Awning Window is a great option with its modern styling, convenient size, and a large awning that tilts out for excellent ventilation. The Crank window has a lower glass panel that tilts out like an awning for an abundance of ventilation. Popular on Conversion and as a Camper Van Window. *Universal Windows have a higher difficulty

FW904RS Outside Frame Dimensions: 33-3/8" X 19-1/8" (848 x 486 mm) Cut out Dimensions: 32-1/2" X 18-1/4" (826 x 464 mm) Clamp Ring/Angles: 1/8 (3 mm) Angles Awning Window can open as much as Approx 7"  The screen is 7-1/4" x 31 1/4"
FW632RS Outside Frame Dimensions: 41-1/4" X 25-3/4" (1048 x 654 mm)   Cut out Dimensions: 40" X 24-1/2" (1016 x 622 mm)   Clamp Ring/Angles: 1/8 (3 mm) Angles Awning Window can open as much as Approx 7" Screen Opening 37-1/2 x 6-1/2"

What's needed to Install?

 No Additional Products Needed 

How will I install this window?

 To install the CRL Universal Awning Van Windows FW904RS/FW632RS Series of bunk windows you will need to create a template. To make a template you can either use the aluminum framing on the backside of the window or the clamp ring we will have illustrations on using the clamp ring. Be sure to use the edge of the clamp ring that matches the aluminum frame edge of the window (the aluminum frame that goes through the wall). 

Make sure that the clamp ring is taped shut as it has an opening. 

 You will then trace your template onto the cardboard box sharpie, black marker, etc.. you do not want to have too wide of a marker as you want to try and be as precise as possible. 

After you have drawn out the pattern on the cardboard it is time to cut the pattern from the cardboard. 

Once your template is created clean up any little rough edges and we are ready to place it on your van. You will want to measure out for placement to ensure you have your template where you want it to be. To hold the template in place you can put screws through the cardboard to hold, have a partner hold or use tape. In our photo we used tape. Be sure to tape the template in place on the straight areas so those are easy to draw in your line later.

Draw your template onto the wall of the van. 

Once you have drawn your pattern onto the wall of the van and are happy with the placement you are ready to cut. Reciprocating saw, skill saw, disc, nibbler, shears, etc... 

Once your hole is done dry-fit the bunk window to make sure the window fits into the hole no adjustments or extra trimming are needed. If you are good you can add a clear coat or paint to the cut edge it's not necessary just a precaution. 

 Now time to install the bunk window. Before putting the window on the van it's best to go through and make a small pilot hole in all the locations around the trim ring that way you do not round the heads of the screws when tightening the window. 

Put Window in place from outside of Van allowing the aluminum mounting frame to extend through a hole in the wall. Place clamp ring from inside most vans will have the split on the bottom. With one person holding the window in place on the outside the other can start to screw from the inside generally start with the two at the split in the trim ring to have that lined up then top and around you do not want to fully tighten once all screws are in place, you can then go back around and tighten them be sure to tighten evenly around for proper seal. 

CRL Universal Awning Van Windows - FW904RS

CRL Universal Awning Van Windows - FW632RS

Should you purchase a Universal Window? 

If you have a Sprinter, ProMaster, or Transit. Direct-Fit Windows are the superior option to a universal window. Universal windows do not take into account body stampings, curvature, or inner structure.  Universal Windows can install on anything and fit nothing. The best practice is to install universal windows within the single sheet metal section of the van wall. Issues that can arise curvature difference can cause buckling of walls or improper seal. Tips to alleviate issues attaching the trim ring of the window incredibly slowly a few threads at a time ensuring that the body and window smoothly come together not forced together. Removing original closed cell foam for a larger open-cell foam that can with curvature difference. Use of thin lauan or other plywood as a backer plate on the inner wall to dissipate pressure. Universal windows are installed at your own risk.