VWD Driver Side Rear Quarter Half-Slider Window Ford Transit 148" EXT Van Med-High Roof 15-21
Part # DTT18012
Mfg Country: Turkey (Europe)
Glass Color = Solar Privacy Glass (Pure Grey Premium Glass)
|Driver Side Rear Quarter
VWD/DOT Glass Half slider Solar Privacy Tint Glass Windows are a premium quality glass window. Manufactured in Europe from the latest and most sophisticated design processes to ensure the window is produced to the highest quality standards. The Windows are then hand polished for the cleanest edges and look in the industry. The OEM style of these van glass windows are modern and fit within the factory body lines for a seamless appearance. The Half-Slider features a push button latch system clean matte black interior frame. Optional All-Metal exterior screen fits seamlessly within the sliders frame and is simple to attach and remove for temporary or full time use.
|Whats needed to Install?|
This window is installed with Urethane Adhesive, you will need a primer base and we recommend edge molding for the cut edge.
Trim Lock Edge Molding (Estimated 12ft)
|How will I install this window?|
REPLACING AN EXISTING OEM WINDOW:
If you are replacing an existing factory window that is urethane bonded, you may want to take to a professional for removal and replacement. If doing on your own best tool to use is a wire cutter Equalizer Window Cut-Out Set . Once the window is cut out you will need to cut the original urethane down as flat as possible and clean as much away as you can we offer CRL Adhesive Cleaner . Other products that can help clean up the existing urethane will be (Acetone, Goo-Gone and WD-40). After using any cleaning product be sure to clean wall with soap and water or rubbing alcohol we also offer PWR22 Cleaner prior to applying new primer and urethane. (Skip to below for window urethane bonding).
ADDING WINDOW TO A VAN WITHOUT WINDOWS:
If you have the following tools cutting can be done on the inside with no template or mirroring of the interior stamping to the outside. (Body Saw, Air Saw, One-Handed Reciprocating Saw)
Drill hole with a bit large enough to accommodate the blade of your cutting tool. Drill within the single sheet metal section that will be cut out then work your blade down to the OEM stamp line. Follow stamp line all the way around section to produce your windows cut hole. (Any interior supports in the window sections can be cut out as they are unnecessary).
**TIP - Cut sides and bottom first leaving the top cut for last so the sheet metal does not start bending while cutting.
Once your hole has been cut, file any rough edges or high points to smooth the cut line. While most will trim and not see the raw edge the smoother and straighter the cut the better the trim will appear when it is time to place it. Once happy with the cut out and filed down smooth, you may want to prime the raw edge of metal prior to installing edge molding. While this is not a necessary step its easy and offers additional piece of mind.
If you will be using the edge molding now will be the time to install it. Window Edge Molding is not necessary for the installation of the window it will be used to offer a better appearance on the interior of the van by covering the raw cut edge. If your interior walls will be covering the cut edge than no reason to trim something that will be hidden. When ordering trim, it is sold from a bulk roll by the foot and there is a drop-down box for proper sizing for your van. Most vans will cover both inner and outer sheet metal edge with the trim. The trim on the outside will not affect the installation of the window as the urethane bead will be taller than the thickness of the trim.
**TIP - There is often an adhesive foam material that is injected between the two sheet metals from the factory. If you are having a tough time getting the trim to cap both sheet metal edges cut the foam away from the cut edge till you can squeeze the metals together and cap with trim molding.
**TIP - Dry fitting window prior to urethane bonding can help familiarize yourself with placement. Also, you can place securing tape/masking/painters’ tape in corners and side middle on to glass then onto body cut tape leaving on both window and van body as added line-up markers for easier placement.
URETHANE BONDING OF WINDOW:
Using a urethane primer apply to the outside of the body you want to apply close to the opening but allow a 1/2" of gap when possible that way when the urethane is applied and spreads less likely to have urethane seeping out from the glass edge on the outside of the van. Only one line of primer is needed and only on the Van wall. Multiple lines and or Primer on the glass is unnecessary and ultimately just a waste of product. After you have painted your primer line around your cut hole allow primer to dry for about 10 minutes.
When using Automotive Urethane, a regular everyday caulking gun will not work. We recommend no less than a 12:1 Thrust Ratio (Commercial/Professional Grade) or above. We offer a 26:1 Ratio Gun in our Tools and Supplies Section.
If you order the urethane from us the tip will have an embossed cutline on the tip showing a cut across the tip as well as a v-notch this will be where you will want to cut the tip for your perfect sized urethane bead. When applying the urethane to the van the V will trail your application patch, so you end up with a pyramid looking bead.
We recommend starting a few inches down from the top rear corner of the window that way you can avoid having a joint from one tube to the next on the top or front of the window. If it happens it is not going to be a catastrophe just if it can be done where the top and front is one continues bead that reduces the risk of a leak. With larger window (Most side OEM fit window) will require a second tube of urethane when one bead end start the next about a 1/2" into the already applied bead (smooth together with plastic putty knife/wood stick, flat screwdriver, etc...) Spraying a liberal amount of glass cleaner onto the tool will help keep the urethane from sticking to the tool and clumping.
**TIP - When applying urethane bead consistency is key to a great install thicker and thinner spots can lead to leakage.
INSTALLING WINDOW TO URETHANE:
Having two people for window placement is always nice one holds the front bottom corner the other the rear bottom corner. OEM fit windows will have about a 1/4" gap from body line to glass get bottom edge lined up holding glass back away from wall on top at a slight angle / once you have your gap lined up at bottom and your front and rear edges are lined up where you want tilt window up and press into urethane you do not need to push too hard as the urethane has a very strong adhesion and will grab on to window quickly. Keep a hand pressing on window to keep position if all good, open hand smack the glass down following the patch of your urethane bead. Goal on modern vans with insert areas for windows will be to get the glass even with the outer body of Van the body above and below the window section so it is a fluid transition from sheet metal to glass to sheet metal again.
Once the window is in the desired location using Window securing tape, tape each corner with 3-4 strips to keep glass in place. If you plan on driving van within the first 24hrs you can also tape the edge all around to keep urethane bead clean from contaminants while traveling.
Once you are ready to install the screen you will want to clean the aluminum frame within the opening of the window well with the provided alcohol pads. Once the surface is clean apply the 3M adhesive promoter to the surface wait 1-2 minutes for the promoter to dry before applying Velcro. The Velcro will be conveniently pre-applied to the backside of the screen. Before removing the Velcro ensure that it is completely flat and attached if the Velcro is wavy, it will not secure properly. With the surface ready and your Velcro flat remove the backing (peel off) from the Velcro to expose the sticky surface. Set your screen into the window cavity and apply pressure to the 3 sides that the screen adheres to. We recommend leaving the screen in place for 72hrs prior to removing it. **For extreme use of off-roading or van life you may want to apply a brushed on super glue to the aluminum surface prior to attaching to Velcro.
|Windows will generally ship in 1-3 Days , shipping time is 1-5 days. Windows will ship via UPS,Fedex , or Freight Truck.|